Materials

3D printing materials

Four engineering materials across SLS, SLA and FFF: tough PA12 nylon, clear resin and carbon- and glass-fibre reinforced polyamide. All printed in our Milton Keynes facility.

Our materials

Choose the right material

PA12 nylon

SLS · Black

A tough, versatile polyamide for functional parts. No supports are needed, so complex shapes, internal channels and assemblies print in one go.

Tensile strength (X-Y)48.2 MPa
Elongation at break22%
Heat deflection, 0.45 MPa147 °C
Melting point184 °C
Density1.02 g/cm³
  • Functional prototypes and end-use parts
  • Complex shapes, internal channels and assemblies
  • Production runs of tens to hundreds of parts

Finishes: Black dyeing, vapour smoothing

Somos® WaterShed

SLA · Transparent

An optically clear resin with ABS- and PBT-like properties and a very smooth surface straight off the machine.

Tensile strength50.4 MPa
Tensile modulus2,770 MPa
Water absorption0.35%
AppearanceOptically clear
  • Clear, see-through parts and covers
  • Fine detail and smooth surfaces
  • Investment casting patterns

Finishes: Sanding, painting, varnishing

DYNAMIDE® CF

FFF · Black

Carbon-fibre reinforced polyamide: our strongest and stiffest material, and the one that takes the most heat.

Tensile strength (X-Y / Z)105 / 66 MPa
Flexural strength165 MPa
Elongation at break3%
Heat deflection, 1.8 MPa195 °C
Heat deflection, 0.45 MPa214 °C
Density1.17 g/cm³
  • Stiff, lightweight brackets and structural parts
  • Jigs, fixtures and tooling
  • Parts that work in hot environments

Finishes: Standard finish

DYNAMIDE® GF

FFF · Grey

Glass-fibre reinforced PA6 with good strength, stiffness and dimensional stability. It can be vapour smoothed for sealed, water-resistant surfaces.

Tensile strength (X-Y / Z)85 / 61.5 MPa
Flexural strength135 MPa
Elongation at break (X-Y)3.5%
Heat deflection, 1.8 MPa122 °C
Heat deflection, 0.45 MPa190 °C
Density1.2 g/cm³
  • Tough end-use parts and housings
  • Outdoor electronic covers
  • Large parts up to 500 x 340 x 485 mm

Finishes: Vapour smoothing

At a glance

Material comparison

Property PA12 nylonSomos® WaterShedDYNAMIDE® CFDYNAMIDE® GF
ProcessSLSSLAFFFFFF
ColourBlackTransparentBlackGrey
Tensile strength (X-Y)48.2 MPa50.4 MPa105 MPa85 MPa
Heat deflection, 0.45 MPa147 °C–214 °C190 °C
Elongation at break22%–3%3.5%
Density1.02 g/cm³–1.17 g/cm³1.2 g/cm³
Vapour smoothingYesNoNoYes

Typical datasheet values, indicative only. Real parts depend on geometry, orientation and finishing. Compare the processes.

FAQs

Material questions

Which material is the strongest?

DYNAMIDE® CF, with a tensile strength of 105 MPa in the X-Y direction. For parts that must be strong in every direction or have complex shapes, PA12 by SLS is often the better choice.

Which material takes the most heat?

DYNAMIDE® CF, with a heat deflection temperature of 214 °C at 0.45 MPa, followed by DYNAMIDE® GF at 190 °C and PA12 at 147 °C.

Which material should I use for clear parts?

Somos® WaterShed by SLA. It is optically clear and has a very smooth surface straight off the machine.

Can I buy DYNAMIDE® filament for my own printer?

Yes. DYNAMIDE® CF, GF, ASA and BREAKAWAY+ are sold in our shop for the LOOP PRO X series.

Not sure which material?

Upload your file for an instant price, or tell us what your part needs to do and our engineers will recommend a material.